Page 420 - Iscar
P. 420
MILLING INSERTS LNKX/LNMT 1506PNTN/PN-N Dimensions S IC328 l IC928 r Tough 1 Hard IC910 10° Ref. r IC4100 Machining Data
W
LNMT
MM
Tangentially Clamped Inserts
ap
with a Reinforced Negative Land
for Unfavorable Conditions
Recommended
DT7150
IC5400
IC908
IC810
ap
fz
l
r
S
W
(mm)
Designation
(mm/t)
LNKX 1506PN-N MM
7.00
6.00
15.00
0.10-0.20
2.00-7.00
7.00
13.88
0.80
LNKX 1506PNTN
•
15.00
6.00
LNKX 150612-PNTN
13.88
2.00-7.00
0.10-0.20
1.20
7.00
•
•
•
LNMT 1506PN-N MM 6.00 15.00 13.88 0.80 ap (1) • • • • • • • 2.00-7.00 0.10-0.20
0.80
0.10-0.20
13.95
15.00
6.00
2.00-7.00
7.00
LNMT 1506PNTN 6.00 15.00 13.95 0.80 7.00 • • • 2.00-7.00 0.10-0.20
LNMT 150616PN-N MM 6.00 15.00 13.95 1.60 7.00 • 2.00-7.00 0.10-0.20
• For cutting speed recommendations, see pages 462-498
(1) D.O.C. when the insert is on the cutter.
For tools, see pages: F90LN-N15 (176) • FDN-CALN15 (300) • SDN-CALN15 (309) • SSB-LN15-R/L (310)
LNKX PNTN LNMT PNTN LNKX/LNMT PN-N-MM
An economical
class insert
S W
LNMW 1506 PNTN 10° Ref.
Tangentially Clamped Insert for
Machining Grey and Nodular Cast Iron l
ap
r
r
Recommended
Dimensions
Machining Data
IC910 ap fz
Designation W l S r ap (1) (mm) (mm/t)
LNMW 1506 PNTN 6.00 15.00 13.98 0.80 7.00 • 2.00-7.00 0.20-0.30
• Flat rake, used for grey cast iron e.g. GG25 170-240 HBR • For cutting speed recommendations, see pages 462-498
(1) DOC when the insert is on the cutter.
For tools, see pages: F90LN-N15 (176) • FDN-CALN15 (300) • SDN-CALN15 (309) • SSB-LN15-R/L (310)
LNKX 1506PN-N PL S W
Tangentially Clamped Inserts with
a Positive Land for Alloyed and l
Stainless Steel and Cast Iron ap
r
Dimensions Tough 1 Hard Recommended
Machining Data
IC328 IC928 IC908 IC910 DT7150 ap fz
Designation W l S r ap (1) (mm) (mm/t)
LNKX 1506PN-N PL 6.00 15.00 13.88 0.80 7.00 • • • • • 2.00-7.00 0.10-0.15
• Positive land (PL), leaves sharp edges without chipping on cast iron components • High shear rake for steel and stainless steel
• For cutting speed recommendations, see pages 462-498
(1) D.O.C. when the insert is on the cutter.
For tools, see pages: F90LN-N15 (176) • FDN-CALN15 (300) • SDN-CALN15 (309) • SSB-LN15-R/L (310)
416 ISCAR