Page 392 - Iscar
P. 392
MILLING INSERTS HM90 ADKT 1505 Dimensions IC330 IC328 F W IC830 Tough 1 Hard IC808 IC908 IC810 IC910 Machining Data
Rd°
Inserts with 2 Helical Cutting
l
ap
Edges for General Use
r
S
Recommended
IC5400
IC950
IC928
IC380
ap
r
S
F
l
W
Designation
(mm)
ap
HM90 ADKT 1505PDR
•
5.80 0.80 2.70
HM90 ADKT 1505PDR-MM 9.60
14.50
5.00-12.00
16.00
•
15.60
9.65
5.92 1.60 1.37
HM90 ADKT 150516-PDR
14.20
5.00-12.00
•
HM90 ADKT 150520-PDR 9.65 16.18 14.50 5.85 0.80 2.16 • • • • • • • • • • • 5.00-12.00
14.20
5.90 2.00 0.79
9.65
15.60
5.00-12.00
HM90 ADKT 150524-PDR 9.65 15.60 14.20 5.80 2.40 0.52 • 5.00-12.00
HM90 ADKT 150532-PDR 9.65 15.20 14.00 5.85 3.20 - • 5.00-12.00
HM90 ADKT 150540-PDR 9.65 14.83 13.90 5.80 4.00 - • 5.00-12.00
HM90 ADKT 150550-PDR 9.65 14.85 13.80 5.75 5.00 - • 5.00-12.00
HM90 ADKT 150564-PDR 9.65 14.85 13.66 5.65 6.40 - • 5.00-12.00
• Inserts with corner radii larger than 0.8 mm should be used on ADK & SM tools only on the face of the cutter
• For cutting speed recommendations, see pages 462-498
For tools, see pages: ADK (210) • F90AD-SFR (179) • HM90 E90AD-15 (25) • HM90 E90AD-CF-15 (25) • HM90 E90AD-M-15 (26) • HM90 F90A-15 (178)
• SM (219)
HM90 ADKT 1505PDR-MM • Cutting edge geometry with low axial angle
• Reinforced cutting edge geometry, which provides better chipping resistance
• Wide frontal wiper that leaves excellent surface finish on the workpiece
• Used for unfavorable conditions and high feeds
W Rd°
HM90 ADCT 1505
General Use Inserts with 2 l
Helical Cutting Edges for High ap
90° Shoulder Accuracy
F r S
Recommended
Dimensions Tough 1 Hard
Machining Data
IC330 IC830 IC380 IC808 ap fz
Designation W l ap S r F (mm) (mm/t)
HM90 ADCT 1505PDR-PL 9.65 16.18 14.50 5.85 0.80 2.16 • • 5.00-8.00 0.08-0.12
HM90 ADCT 150508R-T 9.65 16.18 14.50 5.85 0.80 2.16 • 5.00-8.00 0.08-0.10
HM90 ADCT 150516R-T 9.65 16.18 14.50 5.85 1.60 1.37 • 5.00-8.00 0.08-0.10
HM90 ADCT 150520R-T 9.65 16.18 14.50 5.85 2.00 0.79 • 5.00-8.00 0.08-0.10
HM90 ADCT 150524R-T 9.65 16.18 14.50 5.85 2.40 0.52 • 5.00-8.00 0.08-0.10
HM90 ADCT 150532R-T 9.65 16.18 14.50 5.85 3.20 - • 5.00-8.00 0.08-0.10
HM90 ADCT 150540R-T 9.65 16.18 14.50 5.85 4.00 - • 5.00-8.00 0.08-0.10
HM90 ADCT 150550R-T 9.65 16.18 14.50 5.85 5.00 - • 5.00-8.00 0.08-0.10
HM90 ADCT 150508 PDTR 9.50 15.70 14.00 6.40 0.80 4.10 • • 5.00-12.00 0.08-0.15
• Inserts with corner radii larger than 0.8 mm should be used on ADK & SM tools only on the face of the cutter
• For a more economical insert refer to ADKT 1505PDR-HM in the ADKT 1505PDR family • For cutting speed recommendations, see pages 462-498
For tools, see pages: ADK (210) • F90AD-SFR (179) • HM90 E90AD-15 (25) • HM90 E90AD-CF-15 (25) • HM90 E90AD-M-15 (26) • HM90 F90A-15 (178)
• SM (219)
HM90 ADCT 150508 PDTR HM90 ADCT 1505..R-T HM90 ADCT 1505..PDR-PL
• Sharp ground cutting edge with a special • For machining titanium and super alloys • Designed for optimal machining
edge preparation • Excellent surface finish of stainless steel and high temperature alloys
• Ground all around, including clamping surfaces • Smoother cut • Sharp cutting edge and a positive rake geometry are
• Low axial angle edge geometry • Reduces edge burrs optimized to avoid built-up edge
• Wide sharp-edged wiper for high surface finish • Reduces vibration and noise • Wiper bottom edge leaves an excellent surface finish
• High perpendicularity and mismatch accuracy • Helical axial positive edge geometry
when using tool diameters of up to 50 mm
388 ISCAR