Page 314 - Iscar

SLOTTING CUTTERS
D3
SSB Da
Single-Side Cutting, Disk
Type Slotting Cutters H1 H5
Tmax ap
D

Designation ap D Z Tmax D3 Da H5 H1
SSB D100-12-32-R/L10 9.00 100.00 9 26.00 47.00 32.00 12.00 16.0 SR 14-544/S T-15/51
SSB D125-12-40-R/L10 9.00 125.00 11 35.00 55.00 40.00 12.00 16.0 SR 14-544/S T-15/51
SSB D160-16-40-R/L10 9.00 160.00 13 52.00 55.00 40.00 16.00 20.0 SR 14-544/S T-15/51
For inserts, see pages: QDCT-PDN (427) • QDMT 1205..PDTN-M (427) • QPMT 100408PDTN (425) • SPMT-HQ (426) • XPMT-HQ (426)

Tool Diameter Width of Cutter Type of Insert
80 100 125 160 200 250 8 10 12 14 16 17.5 18 20 22 24 25
QPMT 1004
XPMT 1004
SPMT 1004
(For R.H. cut only)
LNKX 1506
LNMT 1506
LNHT 1506...HT
Without seat

H1 Da
S890 SSB-13
Half Side / Face Disk Milling D D3
Cutters Carrying HELIDO
S890 SNMU 1305 Inserts Tmax
ap
H5
Designation D ap Z Tmax D3 Da H5 H1 kg
S890 SSB D125-20-40-R/L13 125.00 9.00 14 33.00 56.00 40.00 20.00 24.0 1.196 SR 11800745 BLD IP15/S7 SW6-T-SH
For inserts, see pages: S890 SNMU 1305PN... (442)

D3
SSB-LN15-R/L Da Tmax
Single-Side Cutting, Disk
Type Slotting Cutters H5 H1
ap
D

Designation D Z Tmax ap D3 Da H5 H1 kg
SSB D080-22-27-LN15-R/L 80.00 10 18.00 14.00 42.00 27.00 22.00 24.0 0.561 SR 34-535 BLD T15/M7 SW6-T-SH
SSB D100-22-32-LN15-R/L 100.00 12 26.00 14.00 48.00 32.00 22.00 26.0 0.951 SR 34-535 BLD T15/M7 SW6-T-SH
SSB D125-22-40-LN15-R/L 125.00 15 35.00 14.00 56.00 40.00 22.00 26.0 1.515 SR 34-535 BLD T15/M7 SW6-T-SH
SSB D160-22-40-LN15-R/L 160.00 20 52.00 14.00 56.00 40.00 22.00 26.0 2.640 SR 34-535 BLD T15/M7 SW6-T-SH
SSB D200-24-50-LN15-R/L 200.00 25 65.00 14.00 70.00 50.00 24.00 28.0 4.655 SR 34-535 BLD T15/M7 SW6-T-SH
• Note: Left-hand cutters are designated by a yellow groove
For inserts, see pages: LNAT 1506-W (419) • LNAT 1506..PN-N MM (419) • LNAW-15 (CBN) (415) • LNHW 1506 PNTN (ceramic) (418) • LNKX 1506 1.5X45
PN-N (417) • LNKX 1506PN-N PL (416) • LNKX/LNMT 1506PNTN/PN-N MM (416) • LNMT/LNHT 1506...-N HT (418) • LNMT/LNHT 1506PN-R HT (417) • LNMW
1506 PNTN (416)
Gang-Mill Assembly 90º lead angle cutter
SDN and left-hand SSB For D=80 lead angle cutter a=6º
cutters feature two keyways. For D≥100 lead angle cutter a=4.5º
It is recommended to a°
assemble gang-mills
with alternating keyway 14
position. This practice 7
reduces vibration.
LNMT 1506PTNT-HT LNKX 1506... LNMT 1506PN-R-HT
R.H./L.H. LNMT 1506... R.H. only
R.H./L.H.

310 ISCAR