Page 808 - Iscar

ITS BORE CCGT-AF Dimensions d l 80˚ 7˚ d1 S Recommended 93° 97°
95°
95º
95°
80° Rhombic Inserts with a 7°
Positive Flank, Very Positive
Rake Angle and Sharp Cutting
Edge for Machining Aluminum

Machining Data

IC20 ap f
Designation l di S r d1 (mm) (mm/rev)
CCGT 09T308-AF 9.70 9.52 3.97 0.80 4.40 • 0.80-3.00 0.15-0.25
CCGT 120408-AF 12.90 12.70 4.76 0.80 5.50 • 1.00-3.50 0.15-0.30
For tools, see pages: • IHCR (763) • IHRF (787) • IHSR (763) • IHSR-BW (739) • IHSR-C (766) • IHSR-CH (764)

55° 107.5°
DCMT/DCGT-SM 93º 91°
55° Rhombic Inserts with a 7° di d1
Positive Flank for Semi-Finishing 93° 62.5°
and Finish Turning on Soft 7°
Materials and Exotic Alloys r l S

Recommended
Dimensions Tough 1 Hard Machining Data

IC8350 IC6025 IC8250 IC530N IC6015 IC8150 IC520N IC806 IC807 IC907 ap f

Designation l di S r d1 (mm) (mm/rev)
DCMT 070202-SM 7.70 6.35 2.38 0.20 2.80 • • • • 0.50-2.00 0.04-0.20
DCMT 070204-SM 7.70 6.35 2.38 0.40 2.80 • • • • • • • 0.50-2.50 0.05-0.25
DCMT 070208-SM 7.70 6.35 2.38 0.80 2.80 • 0.50-3.00 0.07-0.25
DCGT 11T302-SM 11.60 9.52 3.97 0.20 4.40 • 0.30-2.00 0.05-0.25
DCGT 11T304-SM 11.60 9.52 3.97 0.40 4.40 • 0.50-2.50 0.05-0.25
DCMT 11T302-SM 11.60 9.52 3.97 0.20 4.40 • • • • • • 0.50-2.50 0.05-0.25
DCMT 11T304-SM 11.60 9.52 3.97 0.40 4.40 • • • • • • • • 0.50-2.50 0.07-0.25
DCMT 11T308-SM 11.60 9.52 3.97 0.80 4.40 • • • • • • • 1.00-3.00 0.07-0.25
DCMT 11T312-SM 11.60 9.52 3.97 1.20 4.40 • 1.00-3.50 0.10-0.28
For tools, see page: CHA (760)

55° 107.5°
DCMT-14 93º 91°
55° Rhombic Inserts with a di d1
Positive Flank for Semi-Finishing 93° 62.5°
and Finish Turning on Soft r 7°
Materials and Exotic Alloys l S

Recommended
Dimensions Tough 1 Hard
Machining Data

IC830 IC8150 IC428 ap f
Designation l di S r d1 IC20 (mm) (mm/rev)
DCMT 11T304-14 11.60 9.52 3.97 0.40 4.40 • • • 1.00-2.50 0.14-0.25
DCMT 11T308-14 11.60 9.52 3.97 0.80 4.40 • • • 1.50-3.00 0.14-0.29
For tools, see page: CHA (760)

804 ISCAR